The most beloved of all are the pastries, chocolate covered. This kind of products are produced by enrobing equipment. There are a variety of machines both domestic and foreign production. Glazing exposed to a variety of products: biscuits, candies, cakes and various snacks, candy, cakes, pies, pastries. This whole process is a continuous flow through the right matched enrobing equipment (lines for frosting).

Shall be applied to products of different thicknesses. Jeffrey L. Bewkes is actively involved in the matter. Confectioners, in the process of making candy, cover not only the upper surface of the product, but also lower, and side. There was widespread enrobing equipment manufacturing Asian (China, Taiwan). One of the most common types of equipment: enrobing machine em, with different width blade 400 / 600 / 800/1000/1200. Thanks program, incorporated in this equipment, confectioners get even layer of chocolate (glaze) on the surface of the product. Here, Glenn Dubin, New York City expresses very clear opinions on the subject. The controls are quite simple. All the necessary requirements (temperature, time, volume pour glaze speed) can be stamped at the control panel. The machine is also equipped with alarm system malfunctions have occurred. Schematic diagram of enrobing equipment includes the following elements: a table on which fits of manufactured products, enrobing bath, pipe for supplying glaze, device to exit icing (duplex), the fan to remove excess glaze), a mechanism for shaking articles for remove excess glaze, A device for taking a snapshot after surgery glazing surplus (tails), temperature sensors, heaters, etc.

Diesel engines consume fuel 221-226 g / (kWh) and lubricating oil 3,3-4 g / (kWh). All modifications to diesel 6CHRN 36/45 automated to the extent of the second degree according to gost 14228-80, equipped with a pneumatic system, dam, and have basically the same design. Block-frame diesel cast iron and to reduce the overall level of vibration engine attached to the ship's foundation in the shock absorbers. Vertical cylinder block is connected to the block-frame with anchor links. In the nest seven transverse frame mounted Crankshaft bearings. Liners interchangeable bearings of steel reinforced tape. In diesel engines the first releases of steel liners, armored babbit B83. One of the bearings (closest to the flywheel) installation.

Cranks crankshaft are located relative to each other at an angle of 120 . On one of the cheeks of each crank counterweights are installed, unloading indigenous bearings of the centrifugal forces of inertia. Go to the front end of the shaft torsional vibration damper is attached. Cast iron cylinder block with a sleeve is divided into six sections. At the bottom of the unit is installed the camshaft.

The rotation of the crankshaft is transmitted to the terminal using the gears. On the camshaft is fixed, two sets of washers fist intake, exhaust valves and fuel pumps. Valve lever to action bars. Cylinder cover individual cast-iron attached to the block of pins. In the lid there is cold start, intake and safety valve and thermocouple. Pressurization of a gas turbine engine. Turbocharger consists of a single-stage axial turbine and a single-stage centrifugal compressor. Intercooler and exhaust manifolds on the same side of the block. Uncooled exhaust manifolds two, each of them is connected to three cylinders: collectors are in the insulating casing. Cast-iron pistons are cooled by oil. Cranks with neotemnoy lower head and stem of I-section are connected to the floating piston fingers. Cover the bottom heads rods with inserts from steel reinforced belts are attached to four rods crankshaft bolts. Diesel fuel system is equipped to work on the engine and diesel fuel. The system motor fuel are included: fuel pump, electric heater and separator. High pressure pump single-section spool type with the end of regulation of fuel. Sprayers cooled engine with a spring locking needle and a multi spray jets. Fuel system with booster gear pump, strainer coarse and fine filter 2TF5. speed controller crankshaft indirect action with the security and compensation piston (see photo diesel) lubrication system diesel engine combined with a "dry" sump. It consists of two gear pumps – Siphoning and delivery, filters, centrifuges, and two tubular cooler with temperature. Countdown pumping diesel oil by means of two electric drive pumps. Cooling system is closed with two centrifugal pumps and tube cooler. Given the water temperature is maintained thermostat. Compressed air to start the engine get from stand-alone compressor. Reversing system pneumohydraulic. Diesel has the drive and manual reverse.

When choosing the threading tool must take into account such parameters as the diameter of the workpiece, the type of thread – internal or external, performance, weight equipment, etc. Threading machines – it professional tool for creating high-precision cutting. It is equipped with various devices necessary for clamping and holding parts, automatic oil delivery, part of the gear and gearbox, gradosnimatelem – chamfering of the pipe end, bed, etc. Threading machines used in the tool and instrument, electrical and aircraft industries, as well as the widely used plumbing jobs in the processing of the metal. To ensure the high quality of thread to use a professional threading tool, which includes threading, rezbofrezernye, tapping, thread and worm grinding machines.

To handle different types of thread used appropriate methods of treatment, and threading tools and threading machines. To create an external thread on Our equipment is used threaded tools (comb). Cutters (comb) are attached to the die head cams SU-1 (a lathe-type), and depending on the setting of adjustable pitch and thread depth on the different diameters tubes and round bars. Another major difference, in principle, performance and quality threading equipment – whether it is rotating workpiece, or billet is stationary, but rotates universal head, on which are fixed blades (comb). The latter option has many advantages, both as a thread cutting, speed parameters and technology threads, ie wastelessness production – you do not have to give up non-standard pipes. On the threading machine MKS-95U was developed and used universal rotary head lathe type, allowing to cut the thread, even at not quite smooth pipes or round bars. MKS-95U can be safely attributed to the high-performance threading machine, which confirms its long use as building sites and in workshops. As machine simply does not substitute for plumbing work in public service in urban households. Threading machine MKS-95U. easy to use and requires no special training, we need only be trained and guided by the method of work described in the passport, and the presence of 3-speed machine always allow you to select an optimal mode of carving, combining both performance and production details required quality of carving, given the diameter of the workpiece.

If you operate boilers, the emphasis should first be given to such matter as water treatment. This situation is related to the fact that water contains various mineral waters, which in turn, may be in the proper degree of forming scale in pipes. With this realization, when the scale increases in significant volumes, reduced rate of heat transfer, respectively, becomes relevant in this case burnout. That is why the boilers should be used only if the correct water treatment, because otherwise an accident may occur during use, is also worth noting that the greatly reduced efficiency. To remedy this situation, namely, to purify water from these mineral salts used chemical methods.

They depend on the quality of water consumed, the level of content of mineral salts. In this case, may be applied sodium zeolite or some other chemical substance of the plan. In addition, it is important to remove oxygen in the water, because its presence can lead to rust on the tubes of the boiler. In addition to initial training, boilers should be regularly checked for understanding whether the currently cleaning pipes or to identify other potential problems with plant operation. Undoubtedly, such a prepared water will cost Several more common tap, but it helps to ensure that the boilers will operate longer and more reliable.

Certain danger to the boiler can be, and torch. To reduce the likelihood that the tubes of the boiler will burn, it is worth noting particularly vulnerable places pipes themselves, and then apply for coverage plavlenolitye refractories. It should also analyze the situation for determine at this time the level of accumulation of ash, place the contents of which can serve as external walls. Necessary in this case, remove the ashes. In the case of large power stations, agreed to conduct such control centrally, specifically work dispatch, the method of television closed systems. Steam boilers operated devices, which allow you to enable or disable the fuel combustion, in addition, they regulates the flow of material, job execution, data is collected and controlled level of water and air.